7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm +17 dbm output power -30 dbc fundamental leakage smd, 3x3 mm qfn package rohs compliant 100% rf, dc and output power testing features electrical characteristics (ambient temperature t = 25 o c) parameter input frequency range (fin) output frequency range (fout) input return loss (s11) output return loss (s22) saturated output power (psat) rf input power (rf pin) fundamental leakage (fin) third harmonic leakage (3xfin) fourth harmonic leakage (4xfin) bias voltage (vcc) supply current units ghz ghz db db dbm dbm dbc dbc dbc vdc ma min. 7.5 15.0 - - - 0.0 - - - - - typ. - - -15 -7 +17 - - - - +5.0 125 max. 22.5 45.0 - - - +10.0 -30 tbd tbd +5.5 140 page 1 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. april 2006 - rev 28-apr-06 x1000-qt drain bias voltage (vd1,2) gate bias voltage (vg1) gate bias voltage (vg2) supply current (id1,2) (vd=5.0v, vg1=-0.6v, vg2=0.0v typical) source voltage (vss) source current (iss) vdc vdc vdc ma vdc ma - -1.2 -1.2 - -5.5 25 +5.0 -0.6 0.0 220 -5.0 50 +5.5 +0.1 +0.1 250 -2.0 60 absolute maximum ratings supply voltage (vd) supply voltage (vss) supply current (id) supply current (iss) gate bias voltage (vg) input power (rf pin) storage temperature (tstg) operating temperature (ta) channel temperature (tch) +6.0 vdc -6.0 vdc 300 ma 60 ma +0.3 vdc +12.0 dbm -65 to +165 o c -55 to mttf table mttf table 1 (1) channel temperature affects a device's mttf. it is recommended to keep channel temperature as low as possible for maximum life. 1 mimix broadband's 7.5-22.5/15.0-45.0 ghz smd active doubler delivers + 17 dbm of output power. the device combines an active doubler with an output buffer amplifier that delivers constant power over a range of input powers. the device has excellent rejection of the fundamental and harmonic products and requires a single positive bias supply. this device uses mimix broadband's 0.15 gaas phemt device model technology to ensure high reliability and uniformity. the device comes in a low-cost 3x3mm qfn surface mount plastic package offering excellent rf and thermal properties and is rohs compliant. this device is well suited for point-to-point radio, microwave, lmds, satcom and vsat applications. general description
doubler measurements page 2 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm pout for p in = 0 to 10dbm -30 -20 -10 0 10 20 30 7 9 11 13 15 17 19 21 23 25 fin (gh z) pout (dbm) pout ( f inx1), p in=2dbm pout ( f inx1), p in=4dbm pout ( f inx1), p in=6dbm pout ( f inx1), p in=8dbm pout ( f inx1), p in=10dbm pout ( f inx2), p in=2dbm pout ( f inx2), p in=4dbm pout ( f inx2), p in=6dbm pout ( f inx2), p in=8dbm pout ( f inx2), p in=10dbm 2xfin fi n 1 power sweep for fin = 10g hz -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 -15 -10 -5 0 5 10 15 pin (db m) pou t (dbm) pout ( f inx1), f in=10 ghz pout ( f inx2), f in=10 ghz 1 1. measured results taken at room temperature in 40 ghz connectorized test fixture with no de-embedding. x1000-qt april 2006 - rev 28-apr-06
doubler measurements (cont.) page 3 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm x1000-qt april 2006 - rev 28-apr-06 * measured on-wafer with die version of doubler. * measured on-wafer with die version of doubler. harmonic products, pin = +5 dbm (fin = 6 - 20 ghz) -30 -25 -20 -15 -10 -5 0 5 10 15 20 5 1015202530354045 fout (ghz) pout (dbm) fund. (5dbm) 2xfin (5dbm) 3xfin (5dbm) 4xfin (5dbm) 5xfin (5dbm) 6xfin (5dbm) 7xfin (5dbm) fund 2nd (rf out) 3rd 4th 5th 6th 7th harmonic products, pin = +0 dbm (fin = 6 - 20 ghz) -30 -25 -20 -15 -10 -5 0 5 10 15 20 5 1015202530354045 fout (ghz) pout (dbm) fund. (0dbm) 2xfin (0dbm) 3xfin (0dbm) 4xfin (0dbm) 5xfin (0dbm) 6xfin (0dbm) 7xfin (0dbm) fund 2nd (rf out) 3rd 4th 5th 6th 7th
page 4 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm (note: engineering designator is 40dbl0458qt) x1000-qt package dimensions april 2006 - rev 28-apr-06 XX1000-QT wwwwwww p xxxx g top view bottom view
page 5 of 7 pin 3 5 6 7 10 13 15 description rf in vg1 vss vg2 rf out vd2 vd1 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm app note [1] biasing - it is recommended to separately bias each doubler stage with vd(1,2)=5.0v with id1=80ma and id2=140ma and vss=-5.0v with iss=50ma. XX1000-QT provides good performance at reduced bias with vss=-2.0v and iss=25ma. maximum output power is achieved with vss=-5.0v and iss=50ma. separate biasing is recommended if the doubler is to be used at high leve ls of saturation, where gate rectification will alter the effective gate control voltage. it is also recommended to use active bia sing to keep the currents constant as the rf power and temperature vary; this gives the most reproducible results. depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power oper ational amplifier, with a low value resistor in series with the drain supply used to sense the current. the gate of the phemt is contro lled to maintain correct drain current and thus drain voltage. the typical gate voltages needed to do this are vg1=-0.6v and vg2=0.0v. typically the gate is protected with silicon diodes to limit the applied voltage. also, make sure to sequence the applied volta ge to ensure negative gate bias is available before applying the positive drain supply. mttf tables (tbd) these numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricati ng foundry. backplate temperature 55 deg celsius 75 deg celsius 95 deg celsius channel temperature deg celsius deg celsius deg celsius fits e+ e+ e+ mttf hours e+ e+ e+ rth c/w c/w c/w bias conditions: vd1=vd2=4.0v, id1=40 ma, id2=140 ma, vss=-5.0v, iss=50ma x1000-qt april 2006 - rev 28-apr-06 functional schematic top view
page 6 of 7 pcb layout mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm x1000-qt april 2006 - rev 28-apr-06 application circuit rf in rf out vd1 vd2 vg1 vss vg2
page 7 of 7 handling and assembly information caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: do not ingest. do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to aff ect its safety or effectiveness. package attachment - this packaged product from mimix broadband is provided as a rugged surface mount package compatible with high volume solder installation. the package is a low-cost plastic package. vacuum tools or other suitable pick and place equipment may be used to pick and place this part. care should be taken to ensure that there are no voids or gaps in the solder connection so that good rf, dc and ground connections are maintained. voids or gaps can eventually lead not only to rf performance degradation, but reduced reliability and life of the product due to thermal stress. mimix lead-free rohs compliant program - mimix has an active program in place to meet customer and governmental requirements for eliminating lead (pb) and other environmentally hazardous materials from our products. all mimix rohs complian t components are form, fit and functional replacements for their non-rohs equivalents. lead plating of our rohs compliant parts i s 100% matt tin (sn) over copper alloy and is backwards compatible with current standard snpb low-temperature reflow processes as well as higher temperature (260c reflow) ?pb free? processes. part number for ordering description XX1000-QT-0g00 matte tin plated rohs compliant qfn 3x3 16l surface mount package in bulk quantity XX1000-QT-0g0t matte tin plated rohs compliant qfn 3x3 16l surface mount package in tape and reel XX1000-QT-ev1 XX1000-QT evaluation board we also offer this part with snpb (tin-lead) or nipdau plating. please contact your regional sales manager for more information regarding different plating types. mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. typical reflow profiles reflow profile ramp up rate activation time and temperature time above melting point max peak temperature time within 5 oc of peak ramp down rate snpb 3-4 oc/sec 60-120 sec @ 140-160 oc 60-150 sec 240 oc 10-20 sec 4-6 oc/sec pb free 3-4 oc/sec 60-180 sec @ 170-200 oc 60-150 sec 265 oc 10-20 sec 4-6 oc/sec 7.5-22.5/15.0-45.0 ghz active doubler qfn, 3x3 mm x1000-qt april 2006 - rev 28-apr-06
|
